Explore our new Cybersecurity Terms Glossary, explained by our experts.
Cybersecurity Terms Glossary
Substation automation security protects the protection relays, intelligent electronic devices, and IEC 61850 communications that switch and protect the electricity network.

What Is Substation Automation Security?
A substation transforms voltage and switches circuits, and the equipment that decides when to switch is now digital. Protection relays, bay controllers, merging units, and a station computer exchange messages over Ethernet instead of through copper wiring, following the IEC 61850 standard. Substation automation security is the protection of that digital layer, and it is the single most consequential area of electricity cybersecurity, because a substation is where the decision to open a circuit breaker is actually made.
Everything above it, including the control centre and the SCADA layer described under SCADA security, issues requests. The substation acts.
The standard’s original design assumed a physically secure, isolated station network. GOOSE and Sampled Values have no built-in authentication in their base form and are extremely sensitive to timing, which constrains what security can be added without breaking the protection function.
In December 2016, malware later named Industroyer caused a power outage in Kyiv. Its significance was architectural: it included protocol modules for IEC 60870-5-101, IEC 60870-5-104, IEC 61850, and OPC Data Access, meaning it could discover and command grid equipment directly rather than driving an operator’s console remotely, as the 2015 Ukrainian attack had done. It also carried a wiper and a module exploiting a known denial of service flaw in a protection relay.
Industroyer2, deployed against a Ukrainian energy company in April 2022 and disrupted before it could take full effect, was tailored to the specific high-voltage substations of that operator, with device addresses and configuration embedded in the binary. That tailoring is the important detail: the attackers had obtained the station configuration, which means the reconnaissance phase had succeeded long before the attack phase began.
Transmission and distribution operators in Great Britain are operators of essential services under the Network and Information Systems Regulations 2018, with Ofgem as competent authority and assessment against the NCSC Cyber Assessment Framework. Connection and operation obligations under the Grid Code sit alongside, and the long-running substation digitisation programmes mean the installed base is shifting from conventional to digital stations over an extended period, so operators have to secure both at once.
Our OT-SCADA Penetration Test covers digital substations using passive capture, configuration review, and testing against spare or replica equipment, with live work only where the operator can tolerate it.
IEC 62351 defines authentication for GOOSE and Sampled Values, and newer devices support it, but the timing budget is tight and mixed estates complicate deployment because every publisher and subscriber in a group must agree. Many operators therefore rely on strict network isolation and monitoring for the existing estate, and specify authentication support as a procurement requirement for new equipment.
It describes every device, signal, and interlock in the substation, which is exactly what an attacker needs to act precisely rather than destructively. Industroyer2 was tailored to its target’s specific substations, implying the configuration had been obtained first. Treat these files as high-value secrets, control who can export them, and include vendors and consultants in that control.
It has a larger attack surface and better visibility. Hard-wired protection cannot be reconfigured over a network, but it also offers no logging, no anomaly detection, and no rapid reconfiguration during restoration. The digital station is defensible if it is treated as a security zone from the design stage; the risk arises when it is treated as a wiring replacement.
New GOOSE publishers, unexpected changes in state and sequence numbers, MMS write and control operations, configuration downloads, any device appearing that is not in the inventory, and disagreement between time sources. Passive capture on a mirror port gives all of it without touching the protection function, and it is the most productive first step in a substation security programme.
You May Be Interested In These
We use a few cookies that are needed to make this website work, and they are always on. We would also like to set analytics cookies, to see which pages are useful; functional cookies, so that our live chat works; and advertising cookies, to measure our campaigns. We will not set any of those until you say yes, and you can change your mind at any time from the Cookie Settings link in the footer.
Choose the cookies you are happy for us to use. Strictly necessary cookies are always on; everything else is off until you turn it on.
These cookies keep the website working: they hold your security checks, your form submissions and the choice you make here. The site cannot run without them, so they are always on.
These let our live chat open and remember your conversation, and let the newsletter sign-up work. Switch them off and the chat window will not appear.
These tell us which pages are read and how people find us, so that we can improve the site. The reports are about groups of visitors, never about you personally.
These let us measure our advertising and show you our adverts on other websites, such as LinkedIn, Google and Meta. Switch them off and you will still see adverts, but they will be less relevant.