Explore our new Cybersecurity Terms Glossary, explained by our experts.

View the Glossary View the Glossary
PRIVIA

Cybersecurity Terms Glossary

What Is CAN Bus Security?

CAN bus security deals with the in-vehicle network that connects electronic control units, a broadcast bus standardised in ISO 11898 that was designed without authentication or encryption.

Illustration for the cybersecurity term CAN Bus Security
Home / Blog / Cybersecurity Terms / What Is CAN Bus Security?
17 November 2026

What Is CAN Bus Security?

What Is CAN Bus Security?

Every electronic control unit in a conventional vehicle talks to the others over a controller area network. Standardised as ISO 11898 and first shipped by Bosch in the 1980s, CAN is a two-wire differential bus where every node hears every frame and arbitration is decided by the identifier: the lower the identifier, the higher the priority. There is no source address, no authentication, no encryption, and no integrity protection beyond a cyclic redundancy check that exists to catch electrical noise. CAN bus security is the discipline of living with that design in cars, lorries, agricultural machinery, and increasingly in building plant and marine systems.

The Consequences of a Trusting Bus

Because frames carry no proof of origin, any node that can transmit can impersonate any other. A device plugged into the diagnostic connector, a compromised infotainment unit, or a wire tapped behind a wing mirror can send a frame that the braking or steering controller will treat exactly as if the genuine sender had produced it. Four attack shapes follow:

Two Attacks That Changed the Industry

In July 2015, Charlie Miller and Chris Valasek published remote control of a Jeep Cherokee. The entry point was the telematics unit, reachable over the mobile network; from there they reflashed a chip to gain the ability to transmit on CAN, and then sent frames that operated the braking, steering, and transmission. The result was a recall of about 1.4 million vehicles and a permanent change in how regulators discussed vehicle software.

The second is more mundane and more common. From 2022 onwards, researchers investigating a stolen Toyota RAV4 documented CAN injection theft: thieves pull a headlight unit away from the bodywork to reach the wiring, splice a device built into an innocuous-looking case onto the bus, and inject the frames that announce a valid key, unlocking the car and starting the engine in under a minute. The technique works because the frames are trusted, and it has been observed across several manufacturers.

Defending a Protocol That Cannot Be Replaced

CAN will remain in vehicles for decades, so the mitigations wrap around it:

  1. Domain segmentation. A central gateway or domain controller separates the powertrain and chassis buses from infotainment and telematics, filtering which identifiers may cross. This is the control that would have blunted the Jeep attack.
  2. Secure Onboard Communication. The AUTOSAR SecOC specification appends a truncated message authentication code and a freshness counter to safety-relevant frames, so injected and replayed messages are rejected. CAN FD’s larger payload makes this practical.
  3. Intrusion detection on the bus. Because genuine CAN traffic is periodic and the set of identifiers is fixed, timing and entropy anomalies are an unusually reliable detection signal; an injected frame almost always disturbs the cycle.
  4. Hardened diagnostics. Strong, per-vehicle security access algorithms, certificate-based authentication for reprogramming, and signed software images delivered through a verified firmware signing chain.
  5. Physical measures. Alarm triggers on body panel removal, and ultra-wideband ranging for keyless entry to defeat the relay attack variant of the same problem.

Regulation Has Caught Up

Vehicle cybersecurity is no longer voluntary. UNECE Regulation No. 155 requires manufacturers to operate a certified cybersecurity management system covering the whole vehicle lifecycle, and Regulation No. 156 does the same for software updates. Both apply to new vehicle type approvals from July 2022 and to all new vehicles produced from July 2024, and the United Kingdom applies them through its own type approval scheme. ISO/SAE 21434 is the engineering standard manufacturers use to demonstrate compliance, with threat analysis and risk assessment at the item level and a cybersecurity case carried through production and into the field.

Aftermarket devices deserve a mention, because they bypass all of the above. Insurance telematics dongles, fleet trackers, and diagnostic tools plug straight into the OBD-II port, sit on the bus, and frequently offer a mobile data connection with weak authentication. Fleet operators should treat them as an extension of the vehicle’s attack surface and assess them accordingly.

At Privia Security, we test vehicle and embedded platforms down to the bus level through our Hardware Penetration Test Services.

FAQ – Frequently Asked Questions

Why Does CAN Have No Authentication?

It was designed in the 1980s to replace wiring looms with a cheap, deterministic, electrically resilient bus inside a sealed metal box. The threat model was electrical noise and component failure, not an adversary with physical or remote access. Adding cryptography to the original 8-byte payload was also impractical, which is why authentication arrived only with CAN FD and the SecOC specification.

Can Someone Hack a Car Through the OBD-II Port?

Yes, if they can reach the port or a device attached to it. The connector gives direct bus access and exposes diagnostic services that can reprogram control units. Aftermarket insurance and fleet dongles extend that access to the mobile network, and several have been found with weak authentication. Treat any permanently fitted dongle as part of the vehicle’s attack surface.

What Is CAN Injection Theft?

A vehicle theft technique in which the thief reaches the CAN wiring through a headlight or wing mirror aperture, attaches a prepared device, and injects the frames that signal a valid key has been presented. The car unlocks and starts. It exploits the bus’s trust in any frame rather than any flaw in the key fob, and has been documented across several manufacturers since 2022.

Does SecOC Make the Bus Safe?

It closes injection and replay for the frames it protects, which is a significant improvement, but it is applied selectively because of processing cost and bus load. Frames left unprotected remain forgeable, key management across a vehicle’s lifetime is non-trivial, and physical access still permits denial of service. SecOC belongs in a layered design alongside gateway filtering and detection.

Related Terms

You May Be Interested In These

What Is COM Hijacking?

Cybersecurity Terms

17 November 2026

What Is COM Hijacking?

Read More
What Is eIDAS?

Cybersecurity Terms

17 November 2026

What Is eIDAS?

Read More
What Is a Canary Token?

Cybersecurity Terms

17 November 2026

What Is a Canary Token?

Read More