Explore our new Cybersecurity Terms Glossary, explained by our experts.
Cybersecurity Terms Glossary
HackRF One is a wide-band software-defined radio that receives and transmits from 1 MHz to 6 GHz, used to analyse the wireless protocols built into doors, sensors, and controllers.

What Is HackRF?
HackRF One is a software-defined radio designed by Michael Ossmann and sold by Great Scott Gadgets. It covers 1 MHz to 6 GHz, transmits as well as receives, and samples at up to 20 million samples per second. Instead of demodulating a signal in dedicated hardware, it digitises the radio spectrum and hands the raw samples to software, where any protocol can be decoded by writing code rather than by buying a receiver.
For security work this is the whole point. A building’s door controllers, a factory’s telemetry, a hotel’s key system, a car park barrier, and a hospital’s nurse call system all communicate over radio protocols that were designed when nobody expected a general-purpose receiver to cost under two hundred pounds. Software-defined radio made analysing them routine.
| Device | Range | Transmit | Typical use |
|---|---|---|---|
| RTL-SDR dongle | Roughly 24 MHz to 1.7 GHz | No | Receive-only survey and decoding, at very low cost |
| HackRF One | 1 MHz to 6 GHz | Yes, half duplex | General-purpose analysis and replay testing |
| bladeRF and LimeSDR | Varies by model | Yes, full duplex | Protocols needing simultaneous transmit and receive |
| USRP | Wide, model dependent | Yes, full duplex | Research-grade work including cellular base stations |
| Flipper Zero | Sub-GHz plus NFC and infrared | Yes, narrow | Convenient field testing of common low-frequency devices |
HackRF’s trade-offs are worth knowing: it has 8-bit sample resolution, which limits dynamic range, and it is half duplex, so it cannot transmit and receive at the same time. For most assessment work neither matters. For anything resembling a base station, they do.
The software matters more than the radio. GQRX and SDR# provide a waterfall display for finding a signal. Universal Radio Hacker handles capture, demodulation, and protocol reverse engineering with a graphical workflow. GNU Radio builds signal processing chains for anything unusual. The rtl_433 project already decodes several hundred common sensor protocols, which saves a great deal of work on devices that are not bespoke.
A typical sequence runs: identify the frequency, often from the device’s regulatory marking or a filing in a public equipment database; capture a transmission while operating the device; determine the modulation from the waveform; recover the bit stream; and compare several transmissions to see which parts change.
That last step is where the findings come from. If pressing the same button twice produces an identical transmission, the system has no rolling code and is vulnerable to simple replay. If the identifier is sequential across devices, other units can be addressed. If the payload is a fixed-length field with no authentication, commands can be constructed rather than replayed. These are the questions a radio assessment actually answers, and they turn up repeatedly in industrial remote controls, gate openers, and building management sensors.
This is the part that distinguishes radio testing from almost everything else, and it is not optional.
In the UK, the Wireless Telegraphy Act 2006 makes it an offence to install or use wireless telegraphy apparatus without a licence, except where an exemption applies. Receiving is comparatively permissive, though section 48 makes it an offence to intercept a message not intended for you and disclose its content. Transmitting is where the risk sits. Transmitting outside the licence-exempt bands and power limits set out in the relevant Ofcom regulations is unlawful, and deliberately causing interference, such as jamming, carries additional consequences. Interfering with aviation, maritime, or emergency service frequencies is a serious matter.
Practical guidance for anyone doing this work:
Rolling codes with an adequate counter window, challenge and response authentication rather than fixed identifiers, encrypted payloads with per-device keys, and distance bounding or timing checks to resist relay attacks. For anything safety-related, a second independent control path. ETSI EN 303 645 covers the general expectations for consumer connectable products, and the UK PSTI regime has made parts of that enforceable since April 2024.
At Privia Security, our IoT Penetration Testing covers radio interfaces alongside firmware and application layers, under a scope that addresses transmission explicitly.
Owning and receiving with one is generally lawful, although section 48 of the Wireless Telegraphy Act 2006 makes it an offence to intercept a message not intended for you and disclose its contents. Transmitting is the regulated activity: operating outside licence-exempt bands and power limits requires a licence, and deliberately causing interference carries serious consequences.
Whether a remote control or sensor uses a fixed code that can simply be replayed, whether device identifiers are sequential and therefore guessable, whether payloads carry any authentication, and whether commands can be constructed rather than captured. These questions apply to gate controllers, industrial remote controls, building management sensors, and alarm systems, and the answers are frequently uncomfortable.
For receiving and analysis, a twenty-pound RTL-SDR dongle covers a great deal of ground up to roughly 1.7 GHz, and a lot of useful work needs nothing more. HackRF adds transmission, which is required for replay and command construction testing, and extends coverage to 6 GHz. Start with the cheaper device and buy transmit capability when the work requires it.
Use rolling codes with a sensible counter window, or better, challenge and response authentication so that a captured transmission cannot be reused. Encrypt payloads with per-device keys rather than a shared one. Add timing or distance checks to resist relay attacks. For safety-related functions, provide a second independent control path that does not depend on the radio link.
You May Be Interested In These
We use a few cookies that are needed to make this website work, and they are always on. We would also like to set analytics cookies, to see which pages are useful; functional cookies, so that our live chat works; and advertising cookies, to measure our campaigns. We will not set any of those until you say yes, and you can change your mind at any time from the Cookie Settings link in the footer.
Choose the cookies you are happy for us to use. Strictly necessary cookies are always on; everything else is off until you turn it on.
These cookies keep the website working: they hold your security checks, your form submissions and the choice you make here. The site cannot run without them, so they are always on.
These let our live chat open and remember your conversation, and let the newsletter sign-up work. Switch them off and the chat window will not appear.
These tell us which pages are read and how people find us, so that we can improve the site. The reports are about groups of visitors, never about you personally.
These let us measure our advertising and show you our adverts on other websites, such as LinkedIn, Google and Meta. Switch them off and you will still see adverts, but they will be less relevant.