Explore our new Cybersecurity Terms Glossary, explained by our experts.
Cybersecurity Terms Glossary
Smart meter security protects metering devices, the home area network, and the national communications infrastructure that reads them, including the remote disconnect capability they carry.

What Is Smart Meter Security?
A smart meter is a measuring instrument with a radio, a clock, and in most installations a switch capable of cutting the supply to a home. The first three functions attract attention from fraud teams and privacy regulators. The fourth is why national security agencies take an interest, because a population of meters that can be disconnected remotely is, in aggregate, a load-shedding mechanism nobody voted for.
Great Britain has rolled out more than 36 million smart meters, and the architecture used here is unusual internationally: rather than each supplier building its own infrastructure, a single licensed body operates the communications network for all of them.
The GB design treats the meter population as hostile territory and relies on cryptography rather than on network isolation. Commands sent to a meter are signed, and sensitive commands — above all remote disconnection — require authorisation from more than one party, so no single compromised supplier system can disconnect at scale. Device identity is anchored in certificates issued under a dedicated public key infrastructure, and the NCSC contributed to the design and assessment of the architecture. Devices are evaluated under the Commercial Product Assurance scheme before they may be installed.
Participants are audited annually against the Smart Energy Code’s security requirements, and the arrangement means that a supplier with poor internal security cannot by itself endanger the wider system — a deliberate design choice after early concerns that a single compromised supplier could cause national disruption.
Energy suppliers and network operators are the parties with real exposure, and the controls are familiar: segregate the systems that can issue meter commands from general corporate IT, require strong authentication and approval workflows for disconnection commands, log and review every command issued, and treat the DCC interface as a high-value conduit with its own monitoring. The same zone and conduit thinking used in a substation applies to a head-end system.
Electricity distribution and supply are covered by the NIS Regulations 2018 with Ofgem as competent authority, and assessment follows the NCSC’s Cyber Assessment Framework. Smart metering obligations sit alongside that through the Smart Energy Code, so a supplier faces two assurance regimes looking at related systems.
At Privia Security, our IoT Penetration Test Services assess metering devices, home area network implementations, and the head-end platforms that drive them.
Only through an authorised command carried by the DCC, which requires cryptographic authorisation from more than one party. That design exists specifically to stop a single compromised system causing mass disconnection. Supply can still be disconnected legitimately by your supplier under the usual regulatory rules, which is a commercial matter rather than a security one.
Yes. The ZigBee-based link between the meter, communications hub, and in-home display uses encryption and a controlled pairing process managed through the DCC rather than by the householder. The practical residual risk is nearby observation of traffic patterns and attacks on specific device implementations rather than plain interception of readings.
Early meters installed before the national infrastructure was ready were tied to the supplier that fitted them and often lost smart functionality when the customer switched. A programme of enrolment and adoption has migrated most of them onto the DCC network so they operate like SMETS2 devices, though some older units remain in a reduced mode.
The ICO, under the UK GDPR and the Data Protection Act 2018, with sector rules in the Smart Energy Code and licence conditions enforced by Ofgem. Monthly consumption data can generally be read for billing, while daily and half-hourly data require customer consent, and marketing use requires separate, explicit permission.
You May Be Interested In These
We use a few cookies that are needed to make this website work, and they are always on. We would also like to set analytics cookies, to see which pages are useful; functional cookies, so that our live chat works; and advertising cookies, to measure our campaigns. We will not set any of those until you say yes, and you can change your mind at any time from the Cookie Settings link in the footer.
Choose the cookies you are happy for us to use. Strictly necessary cookies are always on; everything else is off until you turn it on.
These cookies keep the website working: they hold your security checks, your form submissions and the choice you make here. The site cannot run without them, so they are always on.
These let our live chat open and remember your conversation, and let the newsletter sign-up work. Switch them off and the chat window will not appear.
These tell us which pages are read and how people find us, so that we can improve the site. The reports are about groups of visitors, never about you personally.
These let us measure our advertising and show you our adverts on other websites, such as LinkedIn, Google and Meta. Switch them off and you will still see adverts, but they will be less relevant.