Explore our new Cybersecurity Terms Glossary, explained by our experts.
Cybersecurity Terms Glossary
A deauthentication attack forges Wi-Fi management frames to disconnect clients from an access point, enabling handshake capture, forced reconnection to a rogue network, or sustained denial of service.

What Is a Deauthentication Attack?
Wi-Fi networks use management frames to handle joining and leaving: association, authentication, beacons, probes, and the deauthentication frame that says a station is no longer connected. In the original 802.11 design none of these frames was protected, so a receiver had no way to tell a genuine deauthentication from a forged one. A deauthentication attack exploits exactly that — spoof the access point’s MAC address, send the frame, and the client drops off the network. Send it repeatedly and the client cannot stay on at all.
The attack needs no credentials and no access to the network. The adversary only has to be within radio range, which for a directional antenna means somewhere down the street.
Practically it is three commands. Put an adapter into monitor mode, identify the target network and its connected stations with airodump-ng, then transmit:
aireplay-ng --deauth 0 -a AA:BB:CC:DD:EE:FF -c 11:22:33:44:55:66 wlan0mon
Supplying a client MAC targets one station; omitting it sends to the broadcast address and clears everyone off. Tools such as mdk4 and bettercap automate the same thing across many networks, and inexpensive microcontroller boards sold as test devices do it at the press of a button.
Disconnection is rarely the objective in itself. Deauthentication is the enabling step for four other things.
IEEE 802.11w, ratified in 2009, added Management Frame Protection. It applies a message integrity check to deauthentication, disassociation, and robust action frames using a key derived during the handshake, so a forged frame is simply discarded. The Wi-Fi Alliance calls it Protected Management Frames.
Adoption was slow because 802.11w was optional under WPA2. Two things changed that: WPA3 makes PMF mandatory, and Wi-Fi 6 certification requires it. Most enterprise access points offer three settings — disabled, capable, and required. Setting it to capable protects modern clients while legacy devices continue to connect unprotected; setting it to required locks out anything that cannot support it, which usually means a small population of older embedded devices that need replacing anyway.
Note that PMF does not stop radio-layer jamming or attacks on frames sent before a session key exists, such as forged beacons and association floods. It closes the specific, trivially cheap technique that most attacks rely on.
A wireless intrusion detection system flags deauthentication frames arriving at an implausible rate or carrying sequence numbers inconsistent with the real access point. Most enterprise controllers include this, and the alert is easy to tune because legitimate deauthentication is rare and bursty rather than continuous. Spectrum analysis distinguishes frame-based attacks from raw interference.
Where wireless is load-bearing — stock systems, point of sale, industrial handhelds — plan for its absence. Enable PMF, keep a wired fallback for anything safety-related, and make sure building security devices use a second channel rather than Wi-Fi alone.
Deliberately interfering with wireless telegraphy is an offence under section 68 of the Wireless Telegraphy Act 2006, and Ofcom treats the sale and use of jamming equipment accordingly. Disrupting a network you have no authority over also engages section 3 of the Computer Misuse Act 1990, which covers unauthorised acts intended to impair the operation of a computer. Testing deauthentication resistance is legitimate work, but only against networks you own or have written authorisation to assess — a point our Penetration Test Services scope explicitly before any wireless engagement begins.
Yes, for the frame-forging technique. WPA3 makes Protected Management Frames mandatory, so deauthentication and disassociation frames carry an integrity check and forged ones are ignored. WPA3 does not prevent radio jamming, attacks on unprotected frames exchanged before a key exists, or a client voluntarily choosing a rogue access point with a stronger signal.
Readily. Enterprise wireless controllers and wireless intrusion detection systems alert on high volumes of deauthentication frames and on frames whose sequence numbers do not match the genuine access point. Because legitimate deauthentication is infrequent, false positives are manageable. Open-source monitoring with a spare adapter in monitor mode works for smaller sites.
Offline cracking of a WPA2 pre-shared key needs the four-way handshake, which is only transmitted when a client associates. Rather than wait for someone to join, the tester forces an existing client off so it reconnects immediately and the handshake is captured. The subsequent attack is a dictionary or brute-force effort against the passphrase, not against the protocol.
Testing equipment you own, in a controlled environment, is normally lawful, but Wi-Fi does not respect boundaries. A broadcast deauthentication in an office block affects neighbouring networks, which brings the Wireless Telegraphy Act 2006 and the Computer Misuse Act 1990 into play. Use targeted frames against known client addresses, keep the duration short, and record the authorisation.
You May Be Interested In These
We use a few cookies that are needed to make this website work, and they are always on. We would also like to set analytics cookies, to see which pages are useful; functional cookies, so that our live chat works; and advertising cookies, to measure our campaigns. We will not set any of those until you say yes, and you can change your mind at any time from the Cookie Settings link in the footer.
Choose the cookies you are happy for us to use. Strictly necessary cookies are always on; everything else is off until you turn it on.
These cookies keep the website working: they hold your security checks, your form submissions and the choice you make here. The site cannot run without them, so they are always on.
These let our live chat open and remember your conversation, and let the newsletter sign-up work. Switch them off and the chat window will not appear.
These tell us which pages are read and how people find us, so that we can improve the site. The reports are about groups of visitors, never about you personally.
These let us measure our advertising and show you our adverts on other websites, such as LinkedIn, Google and Meta. Switch them off and you will still see adverts, but they will be less relevant.