Explore our new Cybersecurity Terms Glossary, explained by our experts.
Cybersecurity Terms Glossary
Z-Wave security covers the S0 and S2 frameworks protecting a sub-gigahertz mesh used in smart locks, alarms, and building controls, where the pairing step decides whether the network can be attacked.

What Is Z-Wave Security?
Z-Wave is a proprietary low-power mesh protocol for home and building automation, operating below 1 GHz — 868.42 MHz in the United Kingdom and the rest of Europe. The lower frequency is its selling point against 2.4 GHz alternatives: better propagation through walls, and no contention with Wi-Fi. It is widely used for smart locks, alarm sensors, blinds, and heating control, which means its security failures have physical consequences.
The protocol is controlled by Silicon Labs, which acquired the technology from Sigma Designs in 2018, and the specification was later opened for public ratification. Its security story divides cleanly into before and after S2.
The original security framework, introduced in 2013, encrypted traffic with AES-128. The encryption was fine. The problem was how the network key reached a new device: during inclusion, the controller sent it protected by a temporary key consisting entirely of zeros.
That value is in the specification, so anyone who captured the pairing exchange could decrypt the network key and then read and inject commands indefinitely. The attack required being within radio range at the moment a device was added — a narrow window in a home, but a much wider one in a building where installers commission dozens of devices over several days.
Security 2 became mandatory for new certifications on 2 April 2017 and replaced that exchange with an elliptic curve Diffie-Hellman agreement over Curve25519. Passive capture of the pairing no longer yields the key.
Protection against an active intermediary comes from out-of-band verification: each device has a Device Specific Key, printed on it as a five-digit number and usually also as a QR code, and the installer enters or scans it during inclusion. The controller checks that the public key it received matches, which an attacker in the middle cannot satisfy.
S2 defines three security classes, and the distinction matters when specifying equipment:
Backwards compatibility undermined this in practice. Because S2 controllers still had to include older S0 devices, the inclusion exchange negotiated which framework to use — and that negotiation was not protected. In May 2018 researchers at Pen Test Partners demonstrated forcing an S2-capable smart lock to pair using S0, after which the zero-key weakness applied and the network key was recoverable. The demonstration used a Yale lock and became known as Z-Shave.
Vendors responded by requiring user notification and confirmation when a downgrade occurs, so the behaviour is visible rather than silent. The underlying lesson holds generally: a protocol is only as strong as the weakest version it will negotiate down to, which is the same structural issue that affects WPA2/WPA3 transition mode.
Z-Wave traffic is captured with a Silicon Labs Zniffer using a compatible USB stick, or from the raw radio with a software-defined radio such as a HackRF or YARD Stick One. The EZ-Wave toolkit, published in 2016, demonstrated discovery, interrogation, and command injection against unsecured devices using SDR hardware. The common findings in assessment are predictable: devices included without security because the installer used a quick-add method, S2 Unauthenticated used where Access Control was required, and a controller sitting on the main corporate or home network with a cloud account protected by a reused password.
Our IoT Penetration Test Services assess Z-Wave estates including inclusion behaviour, which is where the difference between a certified device and a securely deployed one becomes obvious.
It has been required for new product certification since April 2017, so current devices support it. That does not mean a given network uses it. Older devices remain in service, controllers still include them, and an installer in a hurry can pair a capable device without security. Check what security class each node actually negotiated rather than what the box claims.
A value unique to each device, printed on it as five digits and usually also as a QR code, that authenticates the key agreement during inclusion. Entering or scanning it lets the controller confirm it is talking to the intended device rather than an attacker. Skipping this step drops the pairing to S2 Unauthenticated, which an active attacker can intercept.
Yes. The 868 MHz band in the UK is licence exempt and a determined transmitter can suppress communication, which for a sensor means it simply stops reporting. Design around it: use controllers that alert on loss of contact with a node, and never make an alarm or safety function depend on a single wireless path.
Z-Wave uses sub-gigahertz radio, giving better range and no Wi-Fi contention, and operates as a closed certified ecosystem with strong interoperability. Zigbee uses 2.4 GHz, supports higher data rates, and has a more open device market. Security is now comparable: S2 with out-of-band verification is broadly equivalent to Zigbee 3.0 with install codes, and both fail the same way when pairing is rushed.
You May Be Interested In These
We use a few cookies that are needed to make this website work, and they are always on. We would also like to set analytics cookies, to see which pages are useful; functional cookies, so that our live chat works; and advertising cookies, to measure our campaigns. We will not set any of those until you say yes, and you can change your mind at any time from the Cookie Settings link in the footer.
Choose the cookies you are happy for us to use. Strictly necessary cookies are always on; everything else is off until you turn it on.
These cookies keep the website working: they hold your security checks, your form submissions and the choice you make here. The site cannot run without them, so they are always on.
These let our live chat open and remember your conversation, and let the newsletter sign-up work. Switch them off and the chat window will not appear.
These tell us which pages are read and how people find us, so that we can improve the site. The reports are about groups of visitors, never about you personally.
These let us measure our advertising and show you our adverts on other websites, such as LinkedIn, Google and Meta. Switch them off and you will still see adverts, but they will be less relevant.